SUMO ด้ามต๊าปตัวผู้ No.3 (M5-20)
หมวดหมู่สินค้า: SUMO
รหัส :
สนใจติดต่อสอบถามเพิ่มเติม
เพิ่มเพื่อน

19 พฤษภาคม 2564

ผู้ชม 186 ผู้ชม

ด้ามต๊าปตัวผู้ แบบปรับได้ จับตัวเกลียวในได้ทั้งขนาดเล็กและใหญ่ จับได้ทั้งดอกต๊าปและรีมเมอร์ ด้ามยาวจับได้ง่าย แรงบิดดีกว่า

 

รายละเอียด

ด้ามต๊าปตัวผู้ No.3 (M5-20) SUMO

Tap wrench No.3 (M5-20) SUMO

 

ด้ามต๊าป

 



 

การใช้งาน

 

  • ด้ามต๊าปตัวผู้เป็นอุปกรณ์ที่ใช้ในการยึดดอกต๊าปเพื่อทำการต๊าปเกลียว ใช้สำหรับจับทำเกลียวในที่มีขนาดเล็ก
  • หรือใหญ่ได้หลายขนาด และใช้ทำเกลียวงานทั่วๆไป

 

Application

 

  • Tap Wrench is a device used to hold the tap for tapping. Arrested for threading in small or large
  • sizes and threading general

 


วิธีการใช้งาน

 

 

  • ใส่ดอกต๊าปดอกแรกเข้ากับด้าม แล้วนำดอกต๊าปใส่ลงในรูเจาะที่เตรียมไว้
  • ใช้มือจับด้ามต๊าปให้ใกล้ต๊าปมากที่สุด และเริ่มต้นหมุนต๊าป หมุนไปตามเข็มนาฬิกา ใช้กำลังกดพอเหมาะอย่าให้เอียง
  • ให้เปลี่ยนตำแหน่งของมือที่ใช้จับด้ามต๊าปใหม่และให้หมุนไปข้างหน้าประมาณ 1/4 รอบ แล้วหมุนกลับสลับกันไป ในระหว่างนั้นควรหยอดน้ำมันหล่อลื่นเพื่อลดความฝืด และปัดเศษโลหะออกจากชิ้นงานด้วย ทำอย่างนี้ ไปเรื่อยๆ จนสุดระยะของต๊าปหรือสุดระยะของงานที่ต้องการทำเกลียว
  • เปลี่ยนตัวทำเกลียวตัวที่สองและตัวที่สาม ตามลำดับ
  • ทำเกลียวตัวสุดท้ายเสร็จ เมื่อเลิกใช้ต้องเช็ดให้สะอาดและเก็บเข้าที่ให้เรียบร้อย

 

How to use

 

  • Put the first tap with the handle then put the tap into the hole prepared.
  • Use the handle near the tap to tap most and start spinning rotate clockwise use proper pressure, do not tilt.
  • Change the position of the hand that holds the handle to the new spindle and rotate it forward for about 1/4 turn and rotate back and forth in the meantime, use a lubricant to reduce friction and round off the metal from the work. Do this until the end of the tap or the length of the work to do the spiral
  • Change the thread second and the third respectively.
  • After the last thread was finished, the wipe was cleaned and keep the place. 

 

 

 

คำเตือน

 

  • เศษโลหะที่เกิดจากการตัดเกลียวจะมีความคม จะต้องใช้แปรงปัดออก ไม่ควรใช้มือเพราะจะทำให้เกิดอันตรายได้
  • เวลาหมุนดอกต๊าปควรหมุน 1/4 รอบ แล้วถอยหลังเพื่อป้องกันดอกต๊าปหัก
  • ทำความสะอาดมือ ชิ้นงาน พร้อมทั้งเครื่องมือเสมอ หลังจากที่ทำงานเสร็จทุกครั้ง


Warning

 

  • The scrap of the metal from cutting the thread is very sharp. Use a brush to brush off, Should not be used by bare hand due to its sharpness.
  • The rotation time of the tap should rotate ¼ turn and then back to prevent the break.
  • You should clean your hands, work piece With tools always After finishing all the work.  
Engine by shopup.com